Sets a value for Cell ID. The PathWave Signal Generator software sets Physical Layer Cell ID Group and Physical Layer Cell ID Sector based on this value.

Reference: 3GPP TS 36.211

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:CIDentity <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:CIDentity?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:CIDentity 1 RADio:LTEFdd:WAVeform:CCARrier:DLINk:CIDentity?
Notes	Formula: Cell ID = (3 x Physical Cell ID Group) + Physical Cell ID Sector.
Dependencies	Sets Physical Layer Cell ID Group and Physical Layer Cell ID Sector.
Preset	1
State Saved	Yes
Min	0
Max	503
Initial S/W Revision	A.20.01

Physical Layer Cell ID Group

Displays the Physical Layer Cell ID Group. Value set by software based on Cell ID.

Reference: 3GPP TS 36.211

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:CIDentity:GROup?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:CIDentity:GROup?
Notes	Formula: Cell ID = (3 x Physical Cell ID Group) + Physical Cell ID Sector. Range: 0 to 167 (related to cell ID)
Dependencies	Coupled to Cell ID.
Preset	0
State Saved	Yes
Min	N/A
Max	N/A
Initial S/W Revision	A.20.01

Physical Layer Cell ID Sector

Displays the Physical Layer Cell ID Sector. Value set by software based on Cell ID.

Reference: 3GPP TS 36.211

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:CIDentity:SECTor?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:CIDentity:SECTor?
Note	Formula: Cell ID = (3 x Physical Cell ID Group) + Physical Cell ID Sector. Range: 0 \| 1 \| 2
Dependencies	Coupled to Cell ID.
Preset	1
State Saved	Yes
Min	N/A
Max	N/A
Initial S/W Revision	A.20.01

System Bandwidth

Sets system bandwidth and number of Resource Blocks. The PathWave Signal Generator Software automatically adjusts Total Number of Resource Blocks and Total Number of Occupied Sub-carriers.

Resource blocks and parameters are reconfigured when bandwidth changes.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:BANDwidth B1M4\|B3M\|B5M\|B10M\|B15M\|B20M [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:BANDwidth?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:BANDwidth B10M RADio:LTEFdd:WAVeform:CCARrier:DLINk:BANDwidth?
Dependencies	Sets Total Number of Resource Blocks, Total Number of Occupied Sub-carriers, and Base Sampling Rate.
Preset	B10M
State Saved	Yes
Initial S/W Revision	A.20.01

Total Number of Antennas

Specifies the total number of physical antenna port configurations for the downlink transmission.

Combination with Number of CRS Antenna Ports determines reserved resource elements for cell-specific reference signals.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:APORts:COUNt 1\|2\|4\|8 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:APORts:COUNt?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:APORts:COUNt 1 RADio:LTEFdd:WAVeform:CCARrier:DLINk:APORts:COUNt?
Dependencies
Preset	1
State Saved	Yes
Min	1
Max	8
Initial S/W Revision	A.20.01

Antenna Port

Specifies physical antenna port for transmitting downlink signals. Available selections are determined by Total Number of Antennas.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:APORt <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:APORt?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:APORt 0 RADio:LTEFdd:WAVeform:CCARrier:DLINk:APORt?
Notes	When: Total Number of Antennas is 1, Antenna Port range is 0. Total Number of Antennas is 2, Antenna Port range is 0,1. Total Number of Antennas is 4, Antenna Port range is 0,1,2,3. Total Number of Antennas is 8, Antenna Port range is 0,1,2,3,4,5,6,7.
Preset	0
State Saved	Yes
Min	N/A
Max	N/A
Initial S/W Revision	A.20.01

Power Definition Type

Selects the power definition type for primary cell. Secondary cells (read-only) automatically use the same type.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:POWer:DEFinition TOT\|RSTP [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:POWer:DEFinition?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:POWer:DEFinition TOT RADio:LTEFdd:WAVeform:CCARrier:DLINk:POWer:DEFinition?
Dependencies	All carriers in the aggregation must use the same Power Definition Type. This setting controls read-only state of RSTP and Power.
Preset	TOT
State Saved	Yes
Initial S/W Revision	A.20.01

Reference Signal Transmit Power (RSTP)

Sets the Reference Signal Transmit Power. Automatically calculated from Amplitude, Power, and carrier signal settings.

Reference: 3GPP TS 36.141

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:RSTP?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:RSTP?
Dependencies	Editable only when Power Definition Type is RSTP.
Preset	-40.79
State Saved	Yes
Min	-144 (if power def is RSTP)
Max	10 (if power def is RSTP)
Initial S/W Revision	A.20.01

OFDM Symbol Transmit Power (OSTP)

Displays the OFDM Symbol Transmit Power. Value set by software.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:OSTP?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:OSTP?
Dependencies	If Cyclic Prefix is set to Extended, then OFDM is not visible.
Preset	-13.01
State Saved	Yes
Min	N/A
Max	N/A
Initial S/W Revision	A.20.01

Total Number of Resource Blocks

Displays the total number of resource blocks. The value for this setting is set by the software based on the System Bandwidth setting.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:RB:COUNt?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:RB:COUNt?
Preset	50
State Saved	Yes
Min	N/A
Max	N/A
Initial S/W Revision	A.20.01

Total Number of Occupied Sub-carriers

Displays the total number of occupied sub-carriers. The value for this setting is set by the software based on the System Bandwidth setting.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:SCARrier:COUNt?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:SCARrier:COUNt?
Notes	The center subcarrier is not used for downlink transmission. So, the number of transmitted subcarriers is one less than the number of occupied subcarriers.
Preset	601
State Saved	Yes
Min	N/A
Max	N/A
Initial S/W Revision	A.20.01

Subcarrier Spacing

Displays subcarrier spacing for downlink. Only 15 kHz supported in this release.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:SCARrier:SPACing?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:SCARrier:SPACing?
Preset	15 kHz
State Saved	Yes
Initial S/W Revision	A.20.01

Cyclic Prefix

Selects Normal or Extended cyclic prefix. The PathWave Signal Generator software sets Number of Symbols for Resource Block based on this selection.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:CP NORMal\|EXTended [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:CP?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:CP NORM RADio:LTEFdd:WAVeform:CCARrier:DLINk:CP?
Preset	NORM
State Saved	Yes
Initial S/W Revision	A.20.01

Number of Subcarriers for Resource Block

Displays the number of consecutive subcarriers in downlink resource block. This is always 12.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:RB:SCARrier:COUNt?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:RB:SCARrier:COUNt?
Preset	12
State Saved	Yes
Min	N/A
Max	N/A
Initial S/W Revision	A.20.01

Number of Symbols for Resource Block

Displays the number of consecutive OFDM symbols in the downlink slot.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:RB:SYMBol:COUNt?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:RB:SYMBol:COUNt?
Notes	The value for this setting is set by the software based on Cyclic Prefix (Normal=7, Extended=6).
Preset	7
State Saved	Yes
Min	N/A
Max	N/A
Initial S/W Revision	A.20.01